SIPLUS digital F input modules . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS digital F input modules

| | | | | |

Article number		6AG1136-6BA00-2CA0
		SIPLUS ET 200SP F-DI 4/8x24VDC HF
General information
Product type designation		F-DI 8x24VDC HF
Product function
в—Џ I&M data		Yes; I&M0 to I&M3
Engineering with
в—Џ PROFINET as of GSD version/GSD revision		V2.31
Supply voltage
Rated value (DC)		24 V
permissible range, lower limit (DC)		20.4 V
permissible range, upper limit (DC)		28.8 V
Reverse polarity protection		Yes
Input current
Current consumption (rated value)		75 mA; without load
Current consumption, max.		21 mA; From the backplane bus
Encoder supply
Number of outputs		8
Short-circuit protection		Yes; Electronic (response threshold 0.7 A to 1.8 A)
Output current
в—Џ up to 60 °C, max.		0.3 A
24 V encoder supply
в—Џ 24 V		Yes; min. L+ (-1.5 V)
в—Џ Short-circuit protection		Yes
в—Џ Output current, max.		800 mA; Total current of all encoders
Power
Power available from the backplane bus		70 mW
Power loss
Power loss, typ.		4 W
Address area
Address space per module
в—Џ Inputs		6 byte
в—Џ Outputs		4 byte
Digital inputs
Number of digital inputs		8
Source/sink input		Yes; P-reading
Input characteristic curve in accordance with IEC 61131, type 1		Yes
Input voltage
в—Џ Type of input voltage		DC
в—Џ Rated value (DC)		24 V
в—Џ for signal "0"		-30 to +5V
в—Џ for signal "1"		+15 to +30V
Input current
в—Џ for signal "1", typ.		3.7 mA
Input delay (for rated value of input voltage)
for standard inputs
вЂ” parameterizable		Yes
вЂ” at "0" to "1", min.		0.4 ms
вЂ” at "0" to "1", max.		20 ms
вЂ” at "1" to "0", min.		0.4 ms
вЂ” at "1" to "0", max.		20 ms
for counter/technological functions
вЂ” parameterizable		No
Cable length
в—Џ shielded, max.		1 000 m
в—Џ unshielded, max.		500 m
Interrupts/diagnostics/status information
Diagnostics function		Yes, "Alarms/diagnostic messages" section in the manual
Alarms
в—Џ Diagnostic alarm		Yes
в—Џ Hardware interrupt		No
Diagnostics indication LED
в—Џ RUN LED		Yes; Green LED
в—Џ ERROR LED		Yes; Red LED
в—Џ Monitoring of the supply voltage (PWR-LED)		Yes; green PWR LED
в—Џ Channel status display		Yes; Green LED
в—Џ for channel diagnostics		Yes; Red LED
в—Џ for module diagnostics		Yes; green/red DIAG LED
Potential separation
Potential separation channels
в—Џ between the channels		No
в—Џ between the channels and backplane bus		Yes
в—Џ between the channels and the power supply of the electronics		No
Permissible potential difference
between different circuits		75 V DC/60 V AC
Isolation
Isolation tested with		707 V DC (type test)
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.		-25 °C
в—Џ horizontal installation, max.		60 °C
в—Џ vertical installation, min.		-25 °C
в—Џ vertical installation, max.		50 °C
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width		15 mm
Height		73 mm
Depth		58 mm
Weights
Weight, approx.		49 g