SIPLUS F модули ввода дискретных сигналов . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS F модули ввода дискретных сигналов

| | | | |

SIPLUS F модули ввода дискретных сигналов

Order number		6AG1136-6BA00-2CA0
		SIPLUS ET 200SP F-DI 4/8X24VDC HF
Product type designation
General information
Product function
? I&M data		Yes; I&M0 to I&M3
Engineering with
? STEP 7 TIA Portal can be configured/integrated as of version		V12
? STEP 7 can be configured/integrated as of version		V5.5 SP3 / -
? PROFINET as of GSD version/GSD revision		V2.31
Supply voltage
Type of supply voltage		24 V DC
Rated value (DC)		24 V
Reverse polarity protection		Yes
Encoder supply
Number of outputs		8
short-circuit protection		Yes; Electronic (response threshold 0.7 A to 1.8 A)
Output current
? up to 60 °C, max.		0.3 A
24 V encoder supply
? 24 V		Yes; min. L+ (-1.5 V)
? short-circuit protection		Yes
? Output current, max.		800 mA
Digital inputs
Number of digital inputs		8
m/p-reading		Yes; p-reading
Input characteristic curve in accordance with IEC 61131, type 1		Yes
Input voltage
? Type of input voltage		DC
? Rated value (DC)		24 V
? for signal "0"		-30 to +5V
? for signal "1"		+15 to +30V
Input current
? for signal "1", typ.		3.7 mA
Input delay (for rated value of input voltage)
for standard inputs
— Parameterizable		Yes
for counter/technological functions
— Parameterizable		No
Cable length
? shielded, max.		1 000 m
? Unshielded, max.		500 m
Interrupts/diagnostics/status information
Alarms
? Diagnostic alarm		Yes
? Hardware interrupt		No
Diagnostics indication LED
? RUN LED		Yes; Green LED
? ERROR LED		Yes; Red LED
? Monitoring of the supply voltage (PWR-LED)		Yes; green PWR LED
? Channel status display		Yes; Green LED
? for channel diagnostics		Yes; Red LED
? for module diagnostics		Yes; green/red DIAG LED
Potential separation
Potential separation channels
? between the channels and the backplane bus		Yes
Isolation
Isolation checked with		707 V DC (type test)
Standards, approvals, certificates
Suitable for safety functions		Yes
Highest safety class achievable in safety mode
? Performance level according to EN ISO 13849-1:2008		PLe
? SIL acc. to IEC 61508		SIL 3
? Low demand mode: PFDavg in accordance with SIL3		< 2.00E-05 1/h
? High demand/continuous mode: PFH in accordance with SIL3		< 1.00E-09 1/h
Ambient conditions
Ambient temperature in operation
? horizontal installation, min.		-25 °C
? horizontal installation, max.		60 °C
? vertical installation, min.		-25 °C
? vertical installation, max.		50 °C
Extended ambient conditions
? Relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width		15 mm
Weights
Weight, approx.		49 g