SIPLUS digital F output modules . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS digital F output modules

| | | | |

Article number		6AG1526-2BF00-2AB0
		SIPLUS S7-1500 F-DQ 8x24VDC/2A
General information
Product type designation		F-DQ 8x24VDC/2A PPM
Firmware version
в—Џ FW update possible		Yes
Product function
в—Џ I&M data		Yes; I&M0 to I&M3
Operating mode
в—Џ DQ		Yes
Supply voltage
Rated value (DC)		24 V
permissible range, lower limit (DC)		19.2 V
permissible range, upper limit (DC)		28.8 V
Reverse polarity protection		Yes
Input current
Current consumption (rated value)		110 mA; without load
Output voltage
Rated value (DC)		24 V
Power
Power available from the backplane bus		0.8 W
Power loss
Power loss, typ.		11 W
Address area
Address space per module
в—Џ Address space per module, max.		6 byte
Hardware configuration
Automatic encoding		Yes
в—Џ Electronic coding element type F		Yes
Digital outputs
Number of digital outputs		8
Current-sinking		Yes
Current-sourcing		Yes
Short-circuit protection		Yes
Open-circuit detection		Yes
в—Џ Response threshold, typ.		8 mA
Overload protection		Yes
в—Џ Response threshold, typ.		2.9 A
Limitation of inductive shutdown voltage to		PM-switching: -24 V + (-47 V), PP-switching: -24 V
Switching capacity of the outputs
в—Џ with resistive load, max.		2 A
в—Џ on lamp load, max.		10 W
Load resistance range
в—Џ lower limit		12 в„¦
в—Џ upper limit		2 000 в„¦
Output voltage
в—Џ for signal "1", min.		24 V; L+ (-0.5 V)
Output current
в—Џ for signal "1" rated value		2 A
в—Џ for signal "0" residual current, max.		0.5 mA; Current-sourcing, or current sourcing and sinking switches individually, current sinking: max. 1 mA
Switching frequency
в—Џ with resistive load, max.		30 Hz
в—Џ with inductive load, max.		0.1 Hz
в—Џ on lamp load, max.		10 Hz
Total current of the outputs
в—Џ Current per channel, max.		2 A
Total current of the outputs (per module)
horizontal installation
вЂ” up to 40 °C, max.		16 A
вЂ” up to 60 °C, max.		8 A
vertical installation
вЂ” up to 40 °C, max.		8 A
Cable length
в—Џ shielded, max.		1 000 m
в—Џ unshielded, max.		500 m
Interrupts/diagnostics/status information
Diagnostics function		Yes
Substitute values connectable		No
Alarms
в—Џ Diagnostic alarm		Yes
Diagnostic messages
в—Џ Monitoring the supply voltage		Yes
в—Џ Wire-break		Yes
в—Џ Short-circuit		Yes
в—Џ Group error		Yes
Diagnostics indication LED
в—Џ RUN LED		Yes; Green LED
в—Џ ERROR LED		Yes; Red LED
в—Џ Monitoring of the supply voltage (PWR-LED)		Yes
в—Џ Channel status display		Yes; Green LED
в—Џ for channel diagnostics		Yes; Red LED
в—Џ for module diagnostics		Yes; Red LED
Potential separation
Potential separation channels
в—Џ between the channels		No
в—Џ between the channels and backplane bus		Yes
Isolation
Isolation tested with		707 V DC (type test)
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.		-25 °C; = Tmin
в—Џ horizontal installation, max.		60 °C; = Tmax
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width		35 mm
Height		147 mm
Depth		129 mm
Weights
Weight, approx.		300 g