CM 4 x IO-Link . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на CM 4 x IO-Link

| | | | | |

Article number		6ES7137-6BD00-0BA0
		ET 200SP, CM 4 X IO-LINK ST
General information
Product type designation		CM 4 x IO-Link ST, PU 1
Firmware version		V2.2
в—Џ FW update possible		Yes
usable BaseUnits		BU type A0
Color code for module-specific color identification plate		CC04
Product function
в—Џ I&M data		Yes; I&M0 to I&M3
Engineering with
в—Џ STEP 7 TIA Portal configurable/integrated as of version		STEP 7 V15 or higher
в—Џ STEP 7 configurable/integrated as of version		STEP 7 V5.5 or higher
в—Џ PROFIBUS as of GSD version/GSD revision		One GSD file each, Revision 3 and 5 and higher
в—Џ PROFINET as of GSD version/GSD revision		GSDML V2.3
Supply voltage
Type of supply voltage		24 V DC
Rated value (DC)		24 V
permissible range, lower limit (DC)		19.2 V; 20.5 V if IO-Link is used, as the supply voltage for IO-Link devices has to be at least 20 V at the master.
permissible range, upper limit (DC)		28.8 V
Reverse polarity protection		Yes
Input current
Current consumption, max.		45 mA; without load
Encoder supply
Number of outputs		4
Output current
в—Џ Rated value		200 mA; Per channel
24 V encoder supply
в—Џ Short-circuit protection		Yes
Power loss
Power loss, typ.		1 W
Digital outputs
Cable length
в—Џ unshielded, max.		20 m; Also applies for shielded cables
IO-Link
Number of ports		4
в—Џ of which simultaneously controllable		4
IO-Link protocol 1.0		Yes
IO-Link protocol 1.1		Yes
Transmission rate		4.8 kBaud (COM1); 38.4 kBaud (COM2), 230.4 kBaud (COM3)
Cycle time, min.		2 ms; dynamic, depending on user data length
Size of process data, input per port		32 byte; max.
Size of process data, input per module		144 byte; max.
Size of process data, output per port		32 byte; max.
Size of process data, output per module		128 byte; max.
Memory size for device parameter		2 kbyte; for each port
Master backup		Yes
Configuration without S7-PCT		Yes
Cable length unshielded, max.		20 m
Operating modes
в—Џ IO-Link		Yes
в—Џ DI		Yes
в—Џ DQ		Yes; max. 100 mA per channel
Time Based IO
вЂ” TIO IO-Link IN		No; Only for PROFINET and configuration as version with FW V2.0 or V2.1
вЂ” TIO IO-Link OUT		No; Only for PROFINET and configuration as version with FW V2.0 or V2.1
вЂ” TIO IO-Link IN/OUT		No; Only for PROFINET and configuration as version with FW V2.0 or V2.1
Connection of IO-Link devices
в—Џ Port type A		Yes
в—Џ Port type B		Yes; 24 V DC via external terminal
в—Џ via three-wire connection		Yes
Isochronous mode
Isochronous operation (application synchronized up to terminal)		No; Only for PROFINET and configuration as version with FW V2.0 or V2.1
Interrupts/diagnostics/status information
Alarms
в—Џ Diagnostic alarm		Yes; The port diagnosis is available in the IO-Link mode only.
Diagnostic messages
в—Џ Monitoring the supply voltage		Yes
в—Џ Wire-break		Yes
в—Џ Short-circuit		Yes
в—Џ Group error		Yes
Diagnostics indication LED
в—Џ Monitoring of the supply voltage (PWR-LED)		Yes; green PWR LED
в—Џ Channel status display		Yes; one green LED for channel status Qn (SIO mode) and port status Cn (IO-Link mode) per channel
в—Џ for channel diagnostics		Yes; red Fn LED
в—Џ for module diagnostics		Yes; green/red DIAG LED
Potential separation
Potential separation channels
в—Џ between the channels		No
в—Џ between the channels and backplane bus		Yes
в—Џ between the channels and the power supply of the electronics		No
Isolation
Isolation tested with		707 V DC (type test)
Dimensions
Width		15 mm
Height		73 mm
Depth		58 mm
Weights
Weight, approx.		30 g