PM240 Power Modules . Технические данные. Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на PM240 Power Modules

| | | | | |

Power Modules

General technical specifications

Power Modules	PM240
System operating voltage	380 ... 480 V ±10 % 3 AC
Grid requirement Short-circuit power R_SC	>25 >100 line reactor recommended
Input frequency	47 ... 63 Hz
Output frequency
Control mode V/f	0 ... 550 Hz
Control type Vector	0 ... 240 Hz
Pulse frequency	75 kW (HO): 4 kHz as of 90 kW (HO): 2 kHz Higher pulse frequencies up to 16 kHz, see derating data
Power factor ?	0.7 ... 0.85
Offset factor cos ?	0.95
Inverter efficiency	95 ... 98 %
Output voltage, max. As % of input voltage	95%
Overload capability
Low overload (LO) Note: When the overload capability is used, the base-load current I_L is not reduced.	90 kW (LO): 1.5 ? base-load current I_L (i. e. 150 % overload) for 3 s plus 1.1 ? base-load current I_L (i. e. 110 % overload) for 57 s within a cycle time of 300 s 110 kW and higher (LO): 1.5 ? base-load current I_L (i. e. 150 % overload) for 1 s plus 1.1 ? base-load current I_L (i. e. 110 % overload) for 59 s within a cycle time of 300 s
High overload (HO) Note: When the overload capability is used, the base-load current I_H is not reduced.	75 kW (HO): 2 ? base-load current I_H (i. e. 20 % overload) for 3 s plus 1.5 ? base-load current I_H (i. e. 150 % overload) for 57 s within a cycle time of 300 s 90 kW and higher (HO): 1.6 ? base-load current I_H (i. e. 160 % overload) for 3 s plus 1.36 ? base-load current I_H (i. e. 136 % overload) for 57 s within a cycle time of 300 s
Electromagnetic compatibility	Devices without line filter Devices with line filter class A for compliance with conducted and radiated interference requirements of Category C2
Possible braking methods	DC braking Dynamic braking with integrated braking module
Degree of protection	IP20
Operating temperature
Low overload (LO)	0 ... 40 °C (32 ... 104 °F) without derating >40 ... 60 °C (>104 ... 140 °F) see derating characteristics
High overload (HO)	0 ... 50 °C (32 ... 122 °F) without derating >50 ... 60 °C (>122 ... 140 °F) see derating characteristics
Storage temperature	-40 ... +70 °C (-40 ... +158 °F)
Relative humidity	<95 % RH, condensation not permissible
Cooling	Internal ventilation, power units with increased air cooling by built-in fans
Installation altitude	Up to 1000 m (3281 ft) above sea level without derating, > 1000 m (3281 ft) see derating characteristics
Protection functions	Undervoltage Overvoltage Overcurrent/overload Ground fault Short-circuit Stall protection Motor blocking protection Motor overtemperature Inverter overtemperature Parameter locking
Rated short-circuit current SCCR (Short-Circuit Current Rating) ¹⁾	65 kA
Compliance with standards	UL, cUL, CE, C-Tick, SEMI F47
CE marking	According to Low-Voltage Directive No. 2006/95/EC, EMC Directive 2004/108/EC

¹⁾ Applies to industrial control panel installations acc. to NEC Article 409 or UL 508A/508C.

PM240 Power Modules

Line voltage 380 ... 480 V 3 AC		PM240 Power Modules
Without integrated line filter		6SL3224-0BE37-5UA0	6SL3224-0BE38-8UA0	6SL3224-0BE41-1UA0
With integrated line filter		6SL3224-0BE37-5AA0	–	–
Output current at 50 Hz 400 V 3 AC
Rated current I_rated¹⁾	A	178	205	250
Base-load current I_L¹⁾	A	178	205	250
Base-load current I_H²⁾	A	145	178	205
Maximum current I_max	A	290	308	375
Rated power
Based on I_L	kW (hp)	90 (125)	110 (150)	132 (200)
Based on I_H	kW (hp)	75 (100)	90 (125)	110 (150)
Rated pulse frequency	kHz	4	2	2
Efficiency ?		>0.97	>0.97	>0.97
Power loss ³⁾ at rated current	kW	2.376	2.274	2.964
Cooling air requirement	m³/s (ft³/s)	0.15 (5.3)	0.15 (5.3)	0.15 (5.3)
Sound pressure level L_pA (1 m)	dB	<65	<65	<65
24 V DC power supply for Control Unit	A	1	1	1
Rated input current ⁴⁾
With line reactor	A	186	210	250
Without line reactor	A	204	245	299
Length of cable to braking resistor, max.	m (ft)	15 (49)	15 (49)	15 (49)
Line supply connection U1/L1, V1/L2, W1/L3		M8 screw studs	M8 screw studs	M8 screw studs
Conductor cross-section	mm²	25 ... 120	25 ... 120	25 ... 120
Motor connection U2, V2, W2		M8 screw studs	M8 screw studs	M8 screw studs
Conductor cross-section	mm²	25 ... 120	25 ... 120	25 ... 120
DC link connection, connection for braking resistor DCP/R1, DCN, R2		M8 screw studs	M8 screw studs	M8 screw studs
Conductor cross-section	mm²	25 ... 120	25 ... 120	25 ... 120
PE connection		On housing with M8 screw	On housing with M8 screw	On housing with M8 screw
Motor cable length ⁵⁾, max.
Shielded	m (ft)	50 (164)	50 (164)	50 (164)
Unshielded	m (ft)	100 (328)	100 (328)	100 (328)
Degree of protection		IP20	IP20	IP20
Dimensions
Width	mm (in)	350 (13.78)	350 (13.78)	350 (13.78)
Height
Without integrated line filter	mm (in)	634 (24.96)	634 (24.96)	634 (24.96)
With integrated line filter	mm (in)	934 (36.77)	–	–
Depth
Without operator panel	mm (in)	316 (12.44)	316 (12.44)	316 (12.44)
With operator panel, max.	mm (in)	387 (15.24)	387 (15.24)	387 (15.24)
Frame size		FSF	FSF	FSF
Weight, approx.
Without integrated line filter	kg (lb)	36 (79.4)	39 (86)	39 (86)
With integrated line filter	kg (lb)	52 (115)	–	–

¹⁾ The rated output current I_rated and the base-load current I_L are based on the duty cycle for low overload (LO).

²⁾ The base-load current I_H is based on the duty cycle for high overload (HO).

³⁾ Typical values. You can find additional information on the Internet at http://support.automation.siemens.com/WW/view/en/94059311

⁴⁾ The input current depends on the motor load and line impedance. The input currents apply for rated power loading (based on I_rated) for a line impedance corresponding to u_K = 1 %. These current values without line reactor are specified on the rating plate of the Power Module.

⁵⁾ Max. motor cable length 25 m (82 ft) (shielded) for PM240 Power Modules with integrated line filter to maintain the limit values acc. to EN 61800?3 Category C2.